There are many modifications in the shops frompolyvinyl chloride. In order to understand this question in more detail, it is necessary to consider specific boats. It is also important to note that they can be done on their own. All this can be learned from the article.
Catamarans for fishing under the motor are differentrigid foundation. Frameworks for models are often made of aluminum. On average, the inflatable boat does not exceed 20 kg. In turn, the load capacity parameter is at the level of 300 kg.
To make catamarans for fishing under the motor thehands quite difficult. First of all, a frame is being built. Next, the cylinders are installed on the sides. The skeleton is recommended by many specialists as dural. It is more expedient to choose a small height. On average, the length of the balloon should not be more than 380 cm. For this purpose, polyvinyl chloride should be selected with a high density. After installation of cylinders the baller is fastened. To do this, stretching is used. Also need to install a valve to inflate the boat. The stringer and the boards for the seat are the last.
Inflatable catamarans (PVC) under the motor with a flexiblelocker are found quite often. In this case, the boom is of a small thickness. On the market, modifications from polyvinyl chloride are most often presented. The air valve in the devices is located at the stringer.
On average, the density of the material does not exceed 800 g. per sq. m. meter. The advantage of these boats is the possibility of installing large cylinders. Fastening is found in the cross type. It is an average catamaran (PVC) for a motor in the vicinity of 55 thousand rubles.
For shallow water fishing,boats with rigid lockers. Most often there are models from polyvinyl chloride. In this case, two supports are installed. Directly the cylinders are fixed on the sides of the stringer. In some cases, it is possible to meet modifications with balleries.
The air valves at them are above the boom. On average, the density of the material does not exceed 700 g. per sq. m. meter. Supports for models are fixed above the firmware. Rubber bands are often used. It is an average catamaran (inflatable) for a motor with a rigid locker of about 50 thousand rubles.
Modifications to two beams are of great usedemand. However, it should be borne in mind that only two-seater models are on the market. The index of carrying capacity at them does not exceed 300 kg. Most of the poles are set to a small height. The length of the boat does not exceed 340 cm.
Stringers are often applied with a thickness of about 1.3 mm. The patches of the models are located directly on the cylinders. Double modifications can also be made with flexible lockers. Thus, the nose is considered more secure. Mounting at the catamarans is done through the crossings. Buy a boat in the store for 55 thousand rubles.
Models with three beams are often producedfour-seater type. Their load-carrying capacity is about 500 kg. Runduki often use a little stiffness. However, there are modifications to the two pillars. On the market most often sold are catamarans with two cylinders. It is also important to note that the width of the boat does not exceed 130 cm.
Air valves in such models are locatednear the stringer. The time of filling with air does not exceed 10 minutes. Firmware is most often used for high density. Some boats have a rubber boom. Serving such models are very long. You can buy them at a price of 45 thousand rubles.
Models with low support allow you to installlow-power engines. They are made for two and three cylinders. It is also important to note that the stores have models with stringers. On average, the load capacity does not exceed 300 kg. Cylinders are mainly used for small diameter.
Some modifications use ballier. Stringers in this case are fixed on a polyvinyl chloride pad. Geeks can be made of rubber. They are different in width. Buy a boat with a low sometimes you can at a price of 50 thousand rubles.
Boats with high support are designed for installationpowerful motors. The length of such models exceeds 400 meters. It is also important to note that the cylinders are of large diameter. The chestnuts are mostly of medium hardness. In the market there are both two and three-seat modifications.
The supports are used in this case with an extension. Stringers, as a rule, are installed with a thickness of about 1.4 mm. The density of the material in such modifications is 800 g. per sq. m. meter. Skeletons are made only from durali. You can buy boats in stores for 60 thousand rubles.
These catamarans are very popular. In this case, the payload index is 450 kg. Geeks in the model are used with overlays. The strips are placed on cylinders. The total length of the catamaran does not exceed 350 cm. Stretching is installed on the sides. Firmware is used dense, paddles are included in the standard kit.
It is also important to note that the fastening of the boat is carried out through the crossings. The density of the material is 780 g. per sq. m. meter. Buy this catamaran at a price of 56 thousand rubles.
These catamarans for fishing under the motor "Rotan"are sold with a flexible locker. In this case there are four places. The support is located a short distance from the frame. The total weight of the catamaran does not exceed 22 kg. Firmware is used medium density.
The models are placed at the bottomcylinders. It is also important to note that these modifications use balleries. Stringer is rubber, and its thickness is 1.4 mm. To buy these catamarans in stores can be priced at 45 thousand rubles.
These catamarans for fishing under the motor are madewith rigid lockers. The main advantage of the boat is considered to be strong supports. The indicator of load capacity fluctuates around 500 kg. This catamaran is calculated for four passengers. To protect the bow of the boat used geeks. They are made of rubber, they are flexible.
In the back of the catamaran there is an extension withfirmware. Baller is applied with a wrap. The standard set includes oars. The density of the carcass material is exactly 700 g. per sq. m. meter. The width of the balloon is 46 cm. The carcass mounts are crossed. Buy a model can be for 45 thousand rubles.
These catamarans for fishing under the motor are differenthigh density of material. The specified parameter averages 560 g. per sq. m. meter. Made this boat with two beams. They are installed next to the supports. For the seat there are strong racks. This catamaran is calculated for four passengers. It is also important to note that this model has a durable boom. It is made of polyvinyl chloride. Stretch marks in the model are installed over the beams.
Directly stringer uses a smallthickness. The ballerin in the presented catamaran is absent. The standard set includes oars. In total, the device uses one air valve. Dural is not applied to this model. Also the big diameter of cylinders at a level of 46 cm deserves attention. Buy this catamaran for 47 thousand rubles.
These catamarans for fishing under the motor of manyconsumers like because of tight cylinders. Their diameter is 50 cm. The density of the material is 560 g. per sq. m. meter. Geek in the model is on the cylinders. It is also important to note that it uses rubber panels to protect the coating. Baller is applied with a wrap.
The bow of the catamaran is protected by a stringer. Oars are included in the standard kit. Fastening of the frame takes place through the crossings. The width of this catamaran is 156 cm. The support of the model is not high, so you can install a low-power motor. Buy this catamaran for 52 thousand rubles.
These catamarans (PVC) under the motor for fishingare in great demand. However, it is important to note that this model can accommodate only four people. Geek in this case is not provided. The strips are made of rubber. Stretching in the presented catamaran is located on the cylinders.
The total length of the model is 430 cm. Stringer has a small thickness. The average density of the material is 780 g. per sq. m. meter. In total, the catamaran has two air valves. Buy a model can be for 57 thousand rubles.
</ p>>
