In cases where the computer is not enoughRAM, the swap file of Windows 7 is used. Where this file is located, you will learn by reading the article. In addition, following the advice of experienced users, you will be able to determine the optimal size of the swap file necessary for correct operation of the OS.
In some cases, this file is generally not recommended, as this will affect the speed of the computer. Therefore, the paging file is sometimes disabled. But about everything in order.
There are situations when the operational (physicalmemory) is not enough. For example, you wanted to install a game that requires 4 GB of RAM, but you only have 3 GB on your computer. In this case, the OS uses virtual memory, that is, the swap file (hereinafter referred to as the "FP").
It is worth noting that today the cost of RAM is notis very high, so it's better to buy and install several physical memory slots, since the virtual is on the hard drive and it takes a long time to read it.
As a result, your computer will "slow down". In addition, due to such loads, the service life of HDD or SDD will be reduced.
However, if the AF is correctly configured, it will not increase, "eating" free space on the hard drive, in addition, the fragmentation of the hard disk will be significantly reduced.
By the way, the swap file in Windows XP7 can be transferred from the C (system) drive to another disk, although some users do not advise it.
It is located in one of the partitions of the hard drive and is called pagefile.sys. This is a hidden file, so if you want to see it, you need to activate the visibility of hidden folders and files.
Click "Start" and open the PU. Go to the "Folder Options" section, and then click the "View" tab. Scroll down the slider and click the checkbox next to Show hidden files. Now click "Apply".
Now you can find the Windows 7 paging file. Where it is, you already know (partition of the system disk). But it will not work directly with him. However, there is another way.
If you have enoughthe amount of "RAM", then, most likely, you will want to deactivate the paging file in Windows 7. To do this, you need to click the PCM icon on the "My Computer" icon and select "Properties" in the context menu. There is another way - the "Start" menu, then enter the PU and open the "System" section.
On the left there is a menu where you will need"Additional system parameters". Here you are interested in the "Advanced" tab, the subsection "Speed". Click "Options" and select "Advanced" again. Click "Change" and in the window that opens, clear the checkbox next to the automatic paging file option. Check the "No paging file" option and confirm the settings by clicking "OK". Restart the OS.
So, you learned where in Windows 7 there is a swap file and how to deactivate it.
For the correct operation of a laptop or computeryou will need to properly configure the swap file. First of all, you need to know how much space to allocate under the paging file of Windows 7. Where is it, you remember, so you can independently change its value. Again open the section "Virtual memory" and click "Specify size".
Note: the maximum volume of EP should be approximately 2 times the volume of "RAM". The original size is better to put the same as the maximum. Alternatively, specify the value that is shown opposite the "Recommended" item.
Another important point is the transfer of the swap file from the disk on which you have installed the OS to another hard drive, which will increase the speed.
Now that you know what the Windows 7 swap file is for, setting up and optimizing should not be a problem.
Having listened to the recommendations of experienced users, you can correctly configure the swap file. Here are the main tips:
By the way, the minimum size of the FP should not be less than 1 Gb in order to prevent fragmentation of the HDD.
So, now you understand why you need a filepaging Windows 7, where he is and how to properly configure it. Of course, it would be better not to use a swap file at all, especially since now physical memory is not so expensive. However, if you have an old computer that does not have additional slots for RAM slots, then the swap file is in most cases a necessity, since modern games and programs use quite a lot of "RAM".
With regard to optimization, you canindependently perform all the settings, while following the recommendations of experienced people. This is not so difficult, so you will not have any difficulties. Communicating with experienced users, ask questions, and you will definitely get answers to them.
</ p>>
